Stove Depot

Miflues 316L Mi-FLEX 125mm - 6 Metres

Multi fuel flexible liner made from 316L grade stainless steel.

Product Information:

APPLICATION: A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat.

CONSTRUCTION: The flue liner has a smooth inner liner made from 316L grade stainless steel and is 0.105mm thick. The flue liner has a convoluted outer skin made from 316L stainless steel and is 0.105mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a Omega-Lock seal.

APPROVAL: Flue Liner is approved and listed by HETAS it is also CE approved

Miflues 316L Mi-FLEX 125mm - 8 Metres

Multi fuel flexible liner made from 316L grade stainless steel.

Product Information:

APPLICATION: A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat.

CONSTRUCTION: The flue liner has a smooth inner liner made from 316L grade stainless steel and is 0.105mm thick. The flue liner has a convoluted outer skin made from 316L stainless steel and is 0.105mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a Omega-Lock seal.

APPROVAL: Flue Liner is approved and listed by HETAS it is also CE approved

Miflues 316L Mi-FLEX 125mm - 9 Metres

Multi fuel flexible liner made from 316L grade stainless steel.

Product Information:

APPLICATION: A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat.

CONSTRUCTION: The flue liner has a smooth inner liner made from 316L grade stainless steel and is 0.105mm thick. The flue liner has a convoluted outer skin made from 316L stainless steel and is 0.105mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a Omega-Lock seal.

APPROVAL: Flue Liner is approved and listed by HETAS it is also CE approved

Miflues Finishing Plate 30º-45º - Ø 125

The Finishing Plate comes in two parts and is used to tidy the area around the flue as it passes through a non-combustible wall. This plate is attached to the wall where the flue is passing through between 45° and 60°. Use silicone and screws to secure against the wall.

Product Information:

APPLICATION: For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.

CONSTRUCTION: Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 200kg/m³ TWPro / 128Kg/m3. All parts are fully welded.. Distance to combustibles is 50mm TWPro 60mm on KC

APPROVALS: TWPro is HETAS Approved and is CE marked.. Designation Number . TWPro EN1856-1 T600 N1 W V2 L50040 G50.. TWPro EN1856-1 T200 W V2 L50040 O20. . KC EN1856-1 T600 N1 W V2 L50040 G60.. KC EN1856-1 T200 W V2 L50040 O20.

INSTALLATION: TWPro Twin Wall Insulated Chimney parts are secured together by using a Locking Band.. Make sure that you keep the required distance from the outside of the flue to any combustible material (wood, plaster board).

Miflues Heavy Duty Roof Support - Ø125

The Heavy duty roof Support will rotate on 2 screws so that the flue can be installed vertically through the roof. The Roof Support is attached to the rafters in the roof space, allowing a fixed support before the Flue leaves the structure of the building. The larger plates offer more support than the standard -067 roof support.

Product Information:

APPLICATION: For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.

CONSTRUCTION: Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 200kg/m³ TWPro / 128Kg/m3. All parts are fully welded.. Distance to combustibles is 50mm TWPro 60mm on KC

APPROVALS: TWPro is HETAS Approved and is CE marked.. Designation Number . TWPro EN1856-1 T600 N1 W V2 L50040 G50.. TWPro EN1856-1 T200 W V2 L50040 O20. . KC EN1856-1 T600 N1 W V2 L50040 G60.. KC EN1856-1 T200 W V2 L50040 O20.

INSTALLATION: TWPro Twin Wall Insulated Chimney parts are secured together by using a Locking Band.. Make sure that you keep the required distance from the outside of the flue to any combustible material (wood, plaster board).

Miflues Round Fixed Finishing Plate 45º - Ø 125 - 2pc

The Round Finishing Plate comes in two parts and is used to tidy the area around the flue as it passes through a non-combustible wall. This plate is attached to the wall where the flue is passing through at fixed 45°. Use silicone and screws to secure against the wall. 75mm wide.

Product Information:

APPLICATION: For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.

CONSTRUCTION: Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 200kg/m³ TWPro / 128Kg/m3. All parts are fully welded.. Distance to combustibles is 50mm TWPro 60mm on KC

APPROVALS: TWPro is HETAS Approved and is CE marked.. Designation Number . TWPro EN1856-1 T600 N1 W V2 L50040 G50.. TWPro EN1856-1 T200 W V2 L50040 O20. . KC EN1856-1 T600 N1 W V2 L50040 G60.. KC EN1856-1 T200 W V2 L50040 O20.

INSTALLATION: TWPro Twin Wall Insulated Chimney parts are secured together by using a Locking Band.. Make sure that you keep the required distance from the outside of the flue to any combustible material (wood, plaster board).

Miflues Single Wall to Twin Wall Adaptor - Ø125

Universal adaptor to connect the appliance outlet to the TWPro, can also connect single wall connecting flue or vitreous enamel to TWPro. This has a tapered design to allow a smooth transition from single wall to twin wall.

Product Information:

APPLICATION: For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.

CONSTRUCTION: Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 200kg/m³. All parts are fully welded.. Distance to combustibles is 50mm.

APPROVALS: TWPro is HETAS Approved and is CE marked.. Designation Number . EN1856-1 T600 N1 W V2 L50040 G50.. EN1856-1 T200 W V2 L50040 O20.

INSTALLATION: TWPro Twin Wall Insulated Chimney parts are secured together by using a Locking Band.. Make sure that you keep a distance of 50mm from the outside of the flue to any combustible material (wood, plaster board).

Miflues 135º Tee - Ø125

The 135° Tee is used when you need a cleaning access at the base of the chimney. It is the first piece installed on the external wall and allows for ease cleaning of the flue. The 135° Tee is shaped in such away that it does not restrict the flue gases.

Product Information:

APPLICATION: For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.

CONSTRUCTION: Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 200kg/m³. All parts are fully welded.. Distance to combustibles is 50mm.

APPROVALS: TWPro is HETAS Approved and is CE marked.. Designation Number . EN1856-1 T600 N1 W V2 L50040 G50.. EN1856-1 T200 W V2 L50040 O20.

INSTALLATION: TWPro Twin Wall Insulated Chimney parts are secured together by using a Locking Band.. Make sure that you keep a distance of 50mm from the outside of the flue to any combustible material (wood, plaster board).

Miflues 45º Bend - Ø125

Product Information:

APPLICATION: For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.

CONSTRUCTION: Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 200kg/m³. All parts are fully welded.. Distance to combustibles is 50mm.

APPROVALS: TWPro is HETAS Approved and is CE marked.. Designation Number . EN1856-1 T600 N1 W V2 L50040 G50.. EN1856-1 T200 W V2 L50040 O20.

INSTALLATION: TWPro Twin Wall Insulated Chimney parts are secured together by using a Locking Band.. Make sure that you keep a distance of 50mm from the outside of the flue to any combustible material (wood, plaster board).

Miflues Adjustable Base Support - Ø125

Adjustable Base Supports are used internally or externally to provide vertical support to the chimney. This support has a small levelling adjustment of 50mm to 80mm from the wall surface. Only recommended fixings should be used to fit this base support to the building surface.

Product Information:

APPLICATION: For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.

CONSTRUCTION: Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 200kg/m³. All parts are fully welded.. Distance to combustibles is 50mm.

APPROVALS: TWPro is HETAS Approved and is CE marked.. Designation Number . EN1856-1 T600 N1 W V2 L50040 G50.. EN1856-1 T200 W V2 L50040 O20.

INSTALLATION: TWPro Twin Wall Insulated Chimney parts are secured together by using a Locking Band.. Make sure that you keep a distance of 50mm from the outside of the flue to any combustible material (wood, plaster board).

Miflues TWPro - Adjustable Connecting Pipe 500mm - 125 Ø

500m pipe with an exposed telescopic connecting pipe built into the male end. This has a cover band and insulation to cover the connecting pipe. This can be used to connect directly on to a heating appliance and allows a clean streamlined finish to a stove installation. The disconnector section allows for easy removal of the appliance.

Product Information:

APPLICATION: For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.

CONSTRUCTION: Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 200kg/m³. All parts are fully welded.. Distance to combustibles is 50mm.

APPROVALS: TWPro is HETAS Approved and is CE marked.. Designation Number . EN1856-1 T600 N1 W V2 L50040 G50.. EN1856-1 T200 W V2 L50040 O20.

INSTALLATION: TWPro Twin Wall Insulated Chimney parts are secured together by using a Locking Band.. Make sure that you keep a distance of 50mm from the outside of the flue to any combustible material (wood, plaster board).

Miflues Chest Mounting Plate - Ø125

Transitional plate that converts MI-Flex flue liner to TWPro, the component is designed to be fixed onto the top of a lowered chimney stack. Please note the transition from flex to TWpro must be made in side the existing class 1 chimney stack.

Product Information:

APPLICATION: For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.

CONSTRUCTION: Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 200kg/m³. All parts are fully welded.. Distance to combustibles is 50mm.

APPROVALS: TWPro is HETAS Approved and is CE marked.. Designation Number . EN1856-1 T600 N1 W V2 L50040 G50.. EN1856-1 T200 W V2 L50040 O20.

INSTALLATION: TWPro Twin Wall Insulated Chimney parts are secured together by using a Locking Band.. Make sure that you keep a distance of 50mm from the outside of the flue to any combustible material (wood, plaster board).

Miflues Ø125 Twinwall Pipe - 500mm

Rigid fixed 500mm pipe effective installed length of 465mm.

Product Information:

APPLICATION: For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.

CONSTRUCTION: Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 200kg/m³. All parts are fully welded.. Distance to combustibles is 50mm.

APPROVALS: TWPro is HETAS Approved and is CE marked.. Designation Number . EN1856-1 T600 N1 W V2 L50040 G50.. EN1856-1 T200 W V2 L50040 O20.

INSTALLATION: TWPro Twin Wall Insulated Chimney parts are secured together by using a Locking Band.. Make sure that you keep a distance of 50mm from the outside of the flue to any combustible material (wood, plaster board).

Miflues Roof Support - Ø 125

The Roof Support will rotate on 2 screws so that the flue can be installed vertically through the roof. The Roof Support is attached to the rafters in the roof space, allowing a fixed support before the Flue leaves the structure of the building.

Product Information:

APPLICATION: For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.

CONSTRUCTION: Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 200kg/m³ TWPro / 128Kg/m3. All parts are fully welded.. Distance to combustibles is 50mm TWPro 60mm on KC

APPROVALS: TWPro is HETAS Approved and is CE marked.. Designation Number . TWPro EN1856-1 T600 N1 W V2 L50040 G50.. TWPro EN1856-1 T200 W V2 L50040 O20. . KC EN1856-1 T600 N1 W V2 L50040 G60.. KC EN1856-1 T200 W V2 L50040 O20.

INSTALLATION: TWPro Twin Wall Insulated Chimney parts are secured together by using a Locking Band.. Make sure that you keep the required distance from the outside of the flue to any combustible material (wood, plaster board).

Miflues Tee Cap - Ø125

Used to cap off the bottom or unused end of a 90/135 tee, this is usually fitted to the bottom of a base support to allow easy removal for sweeping and access.

Product Information:

APPLICATION: For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.

CONSTRUCTION: Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 200kg/m³. All parts are fully welded.. Distance to combustibles is 50mm.

APPROVALS: TWPro is HETAS Approved and is CE marked.. Designation Number . EN1856-1 T600 N1 W V2 L50040 G50.. EN1856-1 T200 W V2 L50040 O20.

INSTALLATION: TWPro Twin Wall Insulated Chimney parts are secured together by using a Locking Band.. Make sure that you keep a distance of 50mm from the outside of the flue to any combustible material (wood, plaster board).

Miflues Wall Support 130mm-210mm - Ø 125

Wall support are to be used for lateral support only and should be use a minimum of every 3 metres. Only recommended fixings should be used to fit the wall support to the building surface. This wall band allows you to set a distance of 130mm (minimum) and 210mm (maximum) adjustment from the wall surface allowing a 80mm adjustment. This wall support has to be manually cut down to achieve the desired effective length.

Product Information:

APPLICATION: For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.

CONSTRUCTION: Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 200kg/m³ TWPro / 128Kg/m3. All parts are fully welded.. Distance to combustibles is 50mm TWPro 60mm on KC

APPROVALS: TWPro is HETAS Approved and is CE marked.. Designation Number . TWPro EN1856-1 T600 N1 W V2 L50040 G50.. TWPro EN1856-1 T200 W V2 L50040 O20. . KC EN1856-1 T600 N1 W V2 L50040 G60.. KC EN1856-1 T200 W V2 L50040 O20.

INSTALLATION: TWPro Twin Wall Insulated Chimney parts are secured together by using a Locking Band.. Make sure that you keep the required distance from the outside of the flue to any combustible material (wood, plaster board).

Miflues Wall Support 210mm-420mm - Ø 125

Wall support are to be used for lateral support only and should be use a minimum of every 3 metres. Only recommended fixings should be used to fit the wall support to the building surface. This wall band allows you to set a distance of 80mm (minimum) and 420mm (maximum) adjustment from the wall surface allowing a 340mm adjustment. This wall support has to be manually cut down to achieve the desired effective length.

Product Information:

APPLICATION: For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.

CONSTRUCTION: Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 200kg/m³ TWPro / 128Kg/m3. All parts are fully welded.. Distance to combustibles is 50mm TWPro 60mm on KC

APPROVALS: TWPro is HETAS Approved and is CE marked.. Designation Number . TWPro EN1856-1 T600 N1 W V2 L50040 G50.. TWPro EN1856-1 T200 W V2 L50040 O20. . KC EN1856-1 T600 N1 W V2 L50040 G60.. KC EN1856-1 T200 W V2 L50040 O20.

INSTALLATION: TWPro Twin Wall Insulated Chimney parts are secured together by using a Locking Band.. Make sure that you keep the required distance from the outside of the flue to any combustible material (wood, plaster board).

Miflues Wall Support 50mm-80mm - Ø 125

Wall support are to be used for lateral support only and should be use a minimum of every 3 metres. Only recommended fixings should be used to fit the wall support to the building surface. This wall band allows you to set a distance of 50mm (minimum) and 80mm (maximum) adjustment from the wall surface allowing a 30mm adjustment.

Product Information:

APPLICATION: For use on solid fuel and gas/oil appliances. eg: woodstoves, gas coal effect fires, oil and gas boiler and any solid fuel appliances.

CONSTRUCTION: Outer skin is made from 304 grade stainless steel and is 0.4mm thick. Inner skin is made from 316 grade stainless steel and is 0.4mm thick. Insulation is compressed rockwool giving a density of 200kg/m³ TWPro / 128Kg/m3. All parts are fully welded.. Distance to combustibles is 50mm TWPro 60mm on KC

APPROVALS: TWPro is HETAS Approved and is CE marked.. Designation Number . TWPro EN1856-1 T600 N1 W V2 L50040 G50.. TWPro EN1856-1 T200 W V2 L50040 O20. . KC EN1856-1 T600 N1 W V2 L50040 G60.. KC EN1856-1 T200 W V2 L50040 O20.

INSTALLATION: TWPro Twin Wall Insulated Chimney parts are secured together by using a Locking Band.. Make sure that you keep the required distance from the outside of the flue to any combustible material (wood, plaster board).

Miflues VIT-Smooth - Smooth 45°/135° Elbow - Ø125mm

2 segment 45° Elbow.

Product Information:

APPLICATION: Suitable for gas, oil and solid fuel appliances with temperatures up to 600°.. VIT-Smooth pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System.. VIT-Smooth pipe should NOT be used to pass through ceilings or combustible walls.°

CONSTRUCTION: VIT-Smooth is a single skin connecting flue system manufactured in zero carbon steel with Powder vitreous enamel coating in a matt black finish. . Suitable for gas, oil and solid fuel appliances with temperatures up to 600°.

INSTALLATION: You should not install a piece of VIT-Smooth 100mm within 375mm from combustible material, e.g. wood, plaster boards, etc.. When installing make sure VIT-Smooth is installed the correct way up - the smaller diameter should always be pointing downward.. This is because all the condensates will stay within the flue system and not pass to the outside of the VIT-Smooth.. VIT-Smooth is a friction fit joint so dose not require sealing of the joints, For extra security if desired each joint could be coated with a jointing compound (fire cement or high temperature silicone sealant).This makes sure that no condensate can escape and spoil the appearance of the pipe.. VIT-Smooth has been designed to be cut, but care must be taken to cover any exposed steel with high tempteture paint as this will rust over time.. When installing appropriate PPE should be worn at all times.

MAINTENANCE: You should make provision for inspecting and cleaning the chimney. This is particularly important on solid fuel applications.. You can acheive this by installing a VIT-Smooth with an access doors at changes of direction.. It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Miflues VIT-Smooth - 90° Split Rosette Collar (Flat) - Ø125mm

90° Split Rosette Collar (Flat) retro fit is a decorative cover used to cover the entry hole in to a non-combustible wall or register plate, comes in 2 parts. Used vertical or horizontal at 90 deg.

Product Information:

APPLICATION: Suitable for gas, oil and solid fuel appliances with temperatures up to 600°.. VIT-Smooth pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System.. VIT-Smooth pipe should NOT be used to pass through ceilings or combustible walls.

CONSTRUCTION: VIT-Smooth is a single skin connecting flue system manufactured in zero carbon steel with Powder vitreous enamel coating in a matt black finish. . Suitable for gas, oil and solid fuel appliances with temperatures up to 600°.

INSTALLATION: You should not install a piece of VIT-Smooth 100mm within 375mm from combustible material, e.g. wood, plaster boards, etc.. When installing make sure VIT-Smooth is installed the correct way up - the smaller diameter should always be pointing downward.. This is because all the condensates will stay within the flue system and not pass to the outside of the VIT-Smooth.. VIT-Smooth is a friction fit joint so dose not require sealing of the joints, For extra security if desired each joint could be coated with a jointing compound (fire cement or high temperature silicone sealant).This makes sure that no condensate can escape and spoil the appearance of the pipe.. VIT-Smooth has been designed to be cut, but care must be taken to cover any exposed steel with high tempteture paint as this will rust over time.. When installing appropriate PPE should be worn at all times.

MAINTENANCE: You should make provision for inspecting and cleaning the chimney. This is particularly important on solid fuel applications.. You can acheive this by installing a VIT-Smooth with an access doors at changes of direction.. It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Miflues VIT-Smooth - 90° Tee and Cap M/F - Ø125mm

The 90° Tee is usually installed when you are connecting the flue to the rear outlet of an appliance, a tee cap is included for the base of the tee to allow sweeping access.

Product Information:

APPLICATION: Suitable for gas, oil and solid fuel appliances with temperatures up to 600°.. VIT-Smooth pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System.. VIT-Smooth pipe should NOT be used to pass through ceilings or combustible walls.°

CONSTRUCTION: VIT-Smooth is a single skin connecting flue system manufactured in zero carbon steel with Powder vitreous enamel coating in a matt black finish. . Suitable for gas, oil and solid fuel appliances with temperatures up to 600°.

INSTALLATION: You should not install a piece of VIT-Smooth 100mm within 375mm from combustible material, e.g. wood, plaster boards, etc.. When installing make sure VIT-Smooth is installed the correct way up - the smaller diameter should always be pointing downward.. This is because all the condensates will stay within the flue system and not pass to the outside of the VIT-Smooth.. VIT-Smooth is a friction fit joint so dose not require sealing of the joints, For extra security if desired each joint could be coated with a jointing compound (fire cement or high temperature silicone sealant).This makes sure that no condensate can escape and spoil the appearance of the pipe.. VIT-Smooth has been designed to be cut, but care must be taken to cover any exposed steel with high tempteture paint as this will rust over time.. When installing appropriate PPE should be worn at all times.

MAINTENANCE: You should make provision for inspecting and cleaning the chimney. This is particularly important on solid fuel applications.. You can acheive this by installing a VIT-Smooth with an access doors at changes of direction.. It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Miflues VIT-Smooth - 1000mm Pipe - Ø125mm

Rigid fixed 1000mm pipe effective installed length of 945mm.

Product Information:

APPLICATION: Suitable for gas, oil and solid fuel appliances with temperatures up to 600°.. VIT-Smooth pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System.. VIT-Smooth pipe should NOT be used to pass through ceilings or combustible walls.°

CONSTRUCTION: VIT-Smooth is a single skin connecting flue system manufactured in zero carbon steel with Powder vitreous enamel coating in a matt black finish. . Suitable for gas, oil and solid fuel appliances with temperatures up to 600°.

INSTALLATION: You should not install a piece of VIT-Smooth 100mm within 375mm from combustible material, e.g. wood, plaster boards, etc.. When installing make sure VIT-Smooth is installed the correct way up - the smaller diameter should always be pointing downward.. This is because all the condensates will stay within the flue system and not pass to the outside of the VIT-Smooth.. VIT-Smooth is a friction fit joint so dose not require sealing of the joints, For extra security if desired each joint could be coated with a jointing compound (fire cement or high temperature silicone sealant).This makes sure that no condensate can escape and spoil the appearance of the pipe.. VIT-Smooth has been designed to be cut, but care must be taken to cover any exposed steel with high tempteture paint as this will rust over time.. When installing appropriate PPE should be worn at all times.

MAINTENANCE: You should make provision for inspecting and cleaning the chimney. This is particularly important on solid fuel applications.. You can acheive this by installing a VIT-Smooth with an access doors at changes of direction.. It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Miflues VIT-Smooth - 500mm Pipe - Ø125mm

Rigid fixed 500mm pipe effective installed length of 445mm.

Product Information:

APPLICATION: Suitable for gas, oil and solid fuel appliances with temperatures up to 600°.. VIT-Smooth pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System.. VIT-Smooth pipe should NOT be used to pass through ceilings or combustible walls.°

CONSTRUCTION: VIT-Smooth is a single skin connecting flue system manufactured in zero carbon steel with Powder vitreous enamel coating in a matt black finish. . Suitable for gas, oil and solid fuel appliances with temperatures up to 600°.

INSTALLATION: You should not install a piece of VIT-Smooth 100mm within 375mm from combustible material, e.g. wood, plaster boards, etc.. When installing make sure VIT-Smooth is installed the correct way up - the smaller diameter should always be pointing downward.. This is because all the condensates will stay within the flue system and not pass to the outside of the VIT-Smooth.. VIT-Smooth is a friction fit joint so dose not require sealing of the joints, For extra security if desired each joint could be coated with a jointing compound (fire cement or high temperature silicone sealant).This makes sure that no condensate can escape and spoil the appearance of the pipe.. VIT-Smooth has been designed to be cut, but care must be taken to cover any exposed steel with high temperature paint as this will rust over time.. When installing appropriate PPE should be worn at all times.

MAINTENANCE: You should make provision for inspecting and cleaning the chimney. This is particularly important on solid fuel applications.. You can acheive this by installing a VIT-Smooth with an access doors at changes of direction.. It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Miflues VIT-Smooth - 750mm Pipe - Ø125mm

Rigid fixed 750mm pipe effective installed length of 695mm.

Product Information:

APPLICATION: Suitable for gas, oil and solid fuel appliances with temperatures up to 600°.. VIT-Smooth pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System.. VIT-Smooth pipe should NOT be used to pass through ceilings or combustible walls.°

CONSTRUCTION: VIT-Smooth is a single skin connecting flue system manufactured in zero carbon steel with Powder vitreous enamel coating in a matt black finish. . Suitable for gas, oil and solid fuel appliances with temperatures up to 600°.

INSTALLATION: You should not install a piece of VIT-Smooth 100mm within 375mm from combustible material, e.g. wood, plaster boards, etc.. When installing make sure VIT-Smooth is installed the correct way up - the smaller diameter should always be pointing downward.. This is because all the condensates will stay within the flue system and not pass to the outside of the VIT-Smooth.. VIT-Smooth is a friction fit joint so dose not require sealing of the joints, For extra security if desired each joint could be coated with a jointing compound (fire cement or high temperature silicone sealant).This makes sure that no condensate can escape and spoil the appearance of the pipe.. VIT-Smooth has been designed to be cut, but care must be taken to cover any exposed steel with high tempteture paint as this will rust over time.. When installing appropriate PPE should be worn at all times.

MAINTENANCE: You should make provision for inspecting and cleaning the chimney. This is particularly important on solid fuel applications.. You can acheive this by installing a VIT-Smooth with an access doors at changes of direction.. It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Miflues VIT-Smooth - 1000mm Pipe with Door - Ø125mm

Rigid fixed 1000mm pipe with built in access door to enable sweeping of the flue pipe, effective installed length of 945mm.

Product Information:

APPLICATION: Suitable for gas, oil and solid fuel appliances with temperatures up to 600°.. VIT-Smooth pipe should only be used as a connecting pipe between your appliance and Flue Liner / Chimney Stack / Twin Wall Flue System.. VIT-Smooth pipe should NOT be used to pass through ceilings or combustible walls.

CONSTRUCTION: VIT-Smooth is a single skin connecting flue system manufactured in zero carbon steel with Powder vitreous enamel coating in a matt black finish. . Suitable for gas, oil and solid fuel appliances with temperatures up to 600°.

INSTALLATION: You should not install a piece of VIT-Smooth 100mm within 375mm from combustible material, e.g. wood, plaster boards, etc.. When installing make sure VIT-Smooth is installed the correct way up - the smaller diameter should always be pointing downward.. This is because all the condensates will stay within the flue system and not pass to the outside of the VIT-Smooth.. VIT-Smooth is a friction fit joint so dose not require sealing of the joints, For extra security if desired each joint could be coated with a jointing compound (fire cement or high temperature silicone sealant).This makes sure that no condensate can escape and spoil the appearance of the pipe.. VIT-Smooth has been designed to be cut, but care must be taken to cover any exposed steel with high tempteture paint as this will rust over time.. When installing appropriate PPE should be worn at all times.

MAINTENANCE: You should make provision for inspecting and cleaning the chimney. This is particularly important on solid fuel applications.. You can acheive this by installing a VIT-Smooth with an access doors at changes of direction.. It is recommended that chimneys serving solid fuel appliances be swept and maintained as frequently as necessary but at least once a year.

Miflues 316L Mi-FLEX 125mm - 11 Metres

Multi fuel flexible liner made from 316L grade stainless steel.

Product Information:

APPLICATION: A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat.

CONSTRUCTION: The flue liner has a smooth inner liner made from 316L grade stainless steel and is 0.105mm thick. The flue liner has a convoluted outer skin made from 316L stainless steel and is 0.105mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a Omega-Lock seal.

APPROVAL: Flue Liner is approved and listed by HETAS it is also CE approved

Miflues 316L Mi-FLEX 150mm - 6 Metres

Multi fuel flexible liner made from 316L grade stainless steel.

Product Information:

APPLICATION: A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat.

CONSTRUCTION: The flue liner has a smooth inner liner made from 316L grade stainless steel and is 0.105mm thick. The flue liner has a convoluted outer skin made from 316L stainless steel and is 0.105mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a Omega-Lock seal.

APPROVAL: Flue Liner is approved and listed by HETAS it is also CE approved

Miflues 316L Mi-FLEX 150mm - 8 Metres

Multi fuel flexible liner made from 316L grade stainless steel.

Product Information:

APPLICATION: A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat.

CONSTRUCTION: The flue liner has a smooth inner liner made from 316L grade stainless steel and is 0.105mm thick. The flue liner has a convoluted outer skin made from 316L stainless steel and is 0.105mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a Omega-Lock seal.

APPROVAL: Flue Liner is approved and listed by HETAS it is also CE approved

Miflues 316L Mi-FLEX 150mm - 9 Metres

Multi fuel flexible liner made from 316L grade stainless steel.

Product Information:

APPLICATION: A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat.

CONSTRUCTION: The flue liner has a smooth inner liner made from 316L grade stainless steel and is 0.105mm thick. The flue liner has a convoluted outer skin made from 316L stainless steel and is 0.105mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a Omega-Lock seal.

APPROVAL: Flue Liner is approved and listed by HETAS it is also CE approved

Miflues 316L Mi-FLEX 150mm - 10 Metres

Multi fuel flexible liner made from 316L grade stainless steel.

Product Information:

APPLICATION: A double skinned flexible flue liner suitable for relining within a masonry chimney. Flue liner is suitable for use with burning gas, oil, coal, coke, cured dry logs, cured dry peat.

CONSTRUCTION: The flue liner has a smooth inner liner made from 316L grade stainless steel and is 0.105mm thick. The flue liner has a convoluted outer skin made from 316L stainless steel and is 0.105mm thick. The Flue Liner is constructed from a single strip of steel which is bent at 180 degrees and then the seam is folded in four planes to give a Omega-Lock seal.

APPROVAL: Flue Liner is approved and listed by HETAS it is also CE approved

ACR Woodpecker WP4 4.3KW - Wood Only Stove

Specifications:

- Height: 469mm

- Width: 373mm

- Depth: 360mm

- Output Range: 4.3kw nominal (2Kw min / 5.5Kw max)

- Efficiency: 68.7% gross 75.4% nett

- Hearth Requirement: Superficial non combustible 12mm hearth required (see Bldg Regs) – below 100 degrees

- Weight: 66kg

- Flue Diameter: 125mm

- Smoke Exempt?: Yes – approved by DEFRA for woodburning in smoke controlled areas

- Log Length: 30cm

- EEI classification for ecolabelling 2018: A

Documents:

ACR Brochure

Burley Ashdown 8kW Catalytic Fireball - 9408-C

This stove uses Burley unique Fireball feature giving a highly efficient controllable flame which maximises the heat in your room. Air injection burns most of the ash so less cleaning is required and a unique heat exchanger helps to put more warmth into the house and not up the chimney. The patented air injection system also helps to create a mesmerising fireball flame picture

DEFRA Approved.

Manufactured in the UK.

Specifications:

Documents:

Burley Stove Brochure.pdf

Burley Installation Instructions.pdf

Burley Bradgate 5kW Catalytic Firecube - 9305-C

This stove uses Burley unique Fireball feature giving a highly efficient controllable flame which maximises the heat in your room. Air injection burns most of the ash so less cleaning is required and a unique heat exchanger helps to put more warmth into the house and not up the chimney. The patented air injection system also helps to create a mesmerising fireball flame picture

DEFRA Approved.

Manufactured in the UK.

Specifications:

Documents:

Burley Stove Brochure.pdf

Burley Installation Instructions.pdf

Burley Hardwick 5kW Catalytic Fireball - 9405-C

This stove uses Burley unique Fireball feature giving a highly efficient controllable flame which maximises the heat in your room. Air injection burns most of the ash so less cleaning is required and a unique heat exchanger helps to put more warmth into the house and not up the chimney. The patented air injection system also helps to create a mesmerising fireball flame picture.

DEFRA Approved.

Manufactured in the UK.

Specifications:

Documents:

Burley Stove Brochure.pdf

Burley Installation Instructions.pdf

Burley Icarus 5 5kW - 9605

Specifications:

Documents:

Burley Stove Brochure.pdf

Burley Installation Instructions.pdf

C Cap Capping Cowl For Disused Chimneys - 280mm - Buff

Protect Disused Chimneys With a C-Cap Capping Cowl.

Product Information:

- The C-Cap fits neatly over the chimney pot, where it is retained by galvanised steel spring wires

- Guarantees 100% protection against rain, snow, debris and nesting birds

- 280mm C-Cap fits pots up to 11” external diameter and are supplied with an integral insect screen (optional use), providing additional protection against bees and nesting wasps

- Pots need to be in sound condition, and a cracked pot should either be replaced or suitably strapped to allow insertion of the C-Cap retaining wires

- The C-Cap’s unique design allows continuous, trickle ventilation of the flue

- It can be fitted to any standard round of appropriate size

- Simple fitment in minutes

- Material: Injection-moulded from tough, recyclable ABS thermoplastic

- Colour: Buff

- Size: 280mm

C Cap Capping Cowl For Disused Chimneys - 280mm - Terracotta

Protect Disused Chimneys With a C-Cap Capping Cowl.

Product Information:

- The C-Cap fits neatly over the chimney pot, where it is retained by galvanised steel spring wires

- Guarantees 100% protection against rain, snow, debris and nesting birds

- 280mm C-Cap fits pots up to 11” external diameter and are supplied with an integral insect screen (optional use), providing additional protection against bees and nesting wasps

- Pots need to be in sound condition, and a cracked pot should either be replaced or suitably strapped to allow insertion of the C-Cap retaining wires

- The C-Cap’s unique design allows continuous, trickle ventilation of the flue

- It can be fitted to any standard round of appropriate size

- Simple fitment in minutes

- Material: Injection-moulded from tough, recyclable ABS thermoplastic

- Colour: Terracotta

- Size: 280mm

C Cap Capping Cowl For Disused Chimneys - 330mm - Buff

Protect Disused Chimneys With a C-Cap Capping Cowl.

Product Information:

- The C-Cap fits neatly over the chimney pot, where it is retained by galvanised steel spring wires

- Pots need to be in sound condition, and a cracked pot should either be replaced or suitably strapped to allow insertion of the C-Cap retaining wires

- Guarantees 100% protection against rain, snow, debris and nesting birds

- The larger 330mm C-Cap is designed for 13” pots and does not include an insect screen

- It can be fitted to any standard round of appropriate size

- Simple fitment in minutes

- The C-Cap’s unique design allows continuous, trickle ventilation of the flue

- Material: Injection-moulded from tough, recyclable ABS thermoplastic

- Colour: Buff

- Size: 330mm

C Cap Capping Cowl For Disused Chimneys - 330mm - Terracotta

Protect Disused Chimneys With a C-Cap Capping Cowl.

Product Information:

- The C-Cap fits neatly over the chimney pot, where it is retained by galvanised steel spring wires

- Pots need to be in sound condition, and a cracked pot should either be replaced or suitably strapped to allow insertion of the C-Cap retaining wires

- Guarantees 100% protection against rain, snow, debris and nesting birds

- The larger 330mm C-Cap is designed for 13” pots and does not include an insect screen

- It can be fitted to any standard round of appropriate size

- Simple fitment in minutes

- The C-Cap’s unique design allows continuous, trickle ventilation of the flue

- Material: Injection-moulded from tough, recyclable ABS thermoplastic

- Colour: Terracotta

- Size: 330mm

Cannon Head Chimney Pot - 300mm - Red

To be fixed onto a masonry chimney stack, over the flue liner, to convey combustion gases from a solid fuel fire safely into the atmosphere.

Product Information:

- Suitability: Solid Fuel

- Base Outside Diameter: 300mm

- Base Inside Diameter: 260mm

- Top Outside Diameter: 275mm

- Top Inside Diameter 210mm

- Height: 300mm

- Weight: 9.2kg

- Colour: Red