Hangers, Brackets, Straps & Ties

Joist Hanger with Adjustable Height Strap - 100mm x 270mm

Height adjustable joist hanger for supporting timber joists from timber members.

Product Information:

- A galvanised joist hanger that provides great support with ease of installation.

- Wider strap provides more surface area on the supporting timber and allows increased nail spacing, enhancing the performance of the critical hanger-to-support part of the connection.

- Minimum and maximum nailing schedules are stamped into the strap providing correct installation information for site operatives.

- Speed-prong holds the hanger in position to allow easier attachment. The installer no longer has to try to hold hanger, joist and nail with one hand and swing a hammer with the other!

- JHA270 range features a location tab which allows easier alignment of the hanger.

- The model number and size is stamped into the seat of the hanger for easy identification, even after installation.

- Pre-galvanised mild steel.

Suitable on:

- Solid sawn timber joists.

When to use:

- Face Fix

- Wrap Over

Joist Hanger with Adjustable Height Strap - 100mm x 450mm

Height adjustable joist hanger for supporting timber joists from timber members.

Product Information:

- A galvanised joist hanger that provides great support with ease of installation.

- Wider strap provides more surface area on the supporting timber and allows increased nail spacing, enhancing the performance of the critical hanger-to-support part of the connection.

- Minimum and maximum nailing schedules are stamped into the strap providing correct installation information for site operatives.

- Speed-prong holds the hanger in position to allow easier attachment. The installer no longer has to try to hold hanger, joist and nail with one hand and swing a hammer with the other!

- JHA450 range features longer legs.

- The model number and size is stamped into the seat of the hanger for easy identification, even after installation.

- Pre-galvanised mild steel.

Suitable on:

- Solid sawn timber joists.

When to use:

- Face Fix

- Wrap Over

130mm Long Screw In Wall Tie Stainless Steel With Nylon Wall Plug

Screw in wall ties 130mm stainless steel includes nylon wall plug.

Product information:

- Plastic wall plug included.

- For use when building new brick or block walls directly from existing brickwork.

- Not to be used as a cross cavity wall tie.

- Length: 130mm.

Joist Hanger with Adjustable Height Strap - 150mm x 450mm

Height adjustable joist hanger for supporting timber joists from timber members.

Product Information:

- A galvanised joist hanger that provides great support with ease of installation.

- Wider strap provides more surface area on the supporting timber and allows increased nail spacing, enhancing the performance of the critical hanger-to-support part of the connection.

- Minimum and maximum nailing schedules are stamped into the strap providing correct installation information for site operatives.

- Speed-prong holds the hanger in position to allow easier attachment. The installer no longer has to try to hold hanger, joist and nail with one hand and swing a hammer with the other!

- JHA450 range features longer legs.

- The model number and size is stamped into the seat of the hanger for easy identification, even after installation.

- Pre-galvanised mild steel.

Suitable on:

- Solid sawn timber joists.

When to use:

- Face Fix

- Wrap Over

180mm Long Screw In Wall Tie Stainless Steel With Nylon Wall Plug

Screw in wall ties 130mm stainless steel includes nylon wall plug.

Product information:

- Plastic wall plug included.

- For use when building new brick or block walls directly from existing brickwork.

- Not to be used as a cross cavity wall tie.

- Length: 180mm.

225mm Type 4 Housing Wall Tie Stainless Steel (Box of 250)

Product information:

- Will accept insulation retaining discs / clips.

- Wall tie with a multi drip feature which prevents moisture travelling across the cavity.

- The tie can be installed either way up.

- Length: 225mm.

- Quantity: Box of 250.

250mm Type 4 Housing Wall Tie Stainless Steel (Box of 250)

Product information:

- Will accept insulation retaining discs / clips.

- Wall tie with a multi drip feature which prevents moisture travelling across the cavity.

- The tie can be installed either way up.

- Length: 250mm.

- Quantity: Box of 250.

275mm Type 4 Housing Wall Tie Stainless Steel (Box of 250)

Product information:

- Will accept insulation retaining discs / clips.

- Wall tie with a multi drip feature which prevents moisture travelling across the cavity.

- The tie can be installed either way up.

- Length: 250mm.

- Quantity: Box of 250.

3.75 x 30mm Galv Simpsons Square Twist Nails (Sheradised) - 1kg

N3.75 square twist nails are tested and approved for use when installing Simpson Strong-Tie connectors including joist hangers, brackets and straps. CE marked to EN14592.

Product Information:

Sheradised coating suitable for service class 2 environments.

Suitable On:

- Fastening hangers with straps

- Fastening hangers with top flanges

- Fastening ZS clip for I-beams

- Common Applications

- Fastening connectors to timber including solid wood, composite lumber and glued-laminated timber.

Pack Size: 1 kg

3.75 x 30mm Galv Simpsons Square Twist Nails (Sheradised) - 5kg

N3.75 square twist nails are tested and approved for use when installing Simpson Strong-Tie connectors including joist hangers, brackets and straps. CE marked to EN14592.

Product Information:

Sheradised coating suitable for service class 2 environments.

Suitable On:

- Fastening hangers with straps

- Fastening hangers with top flanges

- Fastening ZS clip for I-beams

- Common Applications

- Fastening connectors to timber including solid wood, composite lumber and glued-laminated timber.

Pack Size: 5 kg

300mm V26 Type 2 Double Triangle Wall Ties - Box of 250

Traditional Double Triangle, general-purpose wall tie used in small commercial buildings and domestic properties. Suitable for buildings with a maximum height of 15m and cavity widths from 0-150mm.

Product Information:

Application - Type 2 - A general-purpose wall tie for applications such as small commercial buildings and domestic properties. They are suitable for buildings with a maximum height if 15m and for flat sites where the basic wind speed is up to 31m/s and altitude is not greater than 150m above sea level. Type 3 - As Type 2 but where the basic wind speed does not exceed 27m/s.

Design - Traditional Double Triangle wall tie previously to BS1243. Multidrip feature to prevent moisture travelling across the cavity. Design means the tie can be installed either way up.

Material - Manufactured from grade 304 stainless steel.

Behaviour in relation to fire - Non combustable (as defined in the national Building  Regulations).

Durability - Excellent corrosion resistance and a service life of not less than 60 years.

Compliance - Tested as Type B (sound) and as Type 2 & 3* (strength) to BS EN 845-1.

Truss Clip - 38mm

The TCP truss clip attaches girders, trusses and rafters to wall plates to provide wind restraint.

Product Information:

- TCP Truss Clips may be used for general purposes, to resist uplift wherever one member crosses another.

- Speed prong provides temporary attachment for ease of installation.

- Obround holes for easier nail driving.

- Pre-galvanised mild steel

Mini Hanger - 47mm

The MHA is a galvanised mini joist hanger suitable for use with regularised timber, rough sawn timber, I-Joists and LVL.

Ideally suited for small timber sections and timber members; such as trimmers and ceiling joists.

Product Information:

- Pre-galvanised mild steel.

47mm Simpsons Ridge Rafter Connector

The RR ridge rafter connector provides alignment control and correct nailing locations. The RR may be used with any rafter slope up to 30°.

Material:

- Pre-galvanised mild steel

Truss Hanger Mono - 47mm

The THM (Truss Hanger Mono) is a joist hanger for supporting mono trusses from timber members.

Product Information:

- Features speed Prongs for ease of installation.

- Pre-galvanised mild steel.

Truss Clip - 47mm

The TCP truss clip attaches girders, trusses and rafters to wall plates to provide wind restraint.

Product Information:

- TCP Truss Clips may be used for general purposes, to resist uplift wherever one member crosses another.

- Speed prong provides temporary attachment for ease of installation.

- Obround holes for easier nail driving.

- Pre-galvanised mild steel

Joist Hanger with Adjustable Height Strap - 47mm x 270mm

Height adjustable joist hanger for supporting timber joists from timber members.

Product Information:

- A galvanised joist hanger that provides great support with ease of installation.

- Wider strap provides more surface area on the supporting timber and allows increased nail spacing, enhancing the performance of the critical hanger-to-support part of the connection.

- Minimum and maximum nailing schedules are stamped into the strap providing correct installation information for site operatives.

- Speed-prong holds the hanger in position to allow easier attachment. The installer no longer has to try to hold hanger, joist and nail with one hand and swing a hammer with the other!

- JHA270 range features a location tab which allows easier alignment of the hanger.

- The model number and size is stamped into the seat of the hanger for easy identification, even after installation.

- Pre-galvanised mild steel.

Suitable on:

- Solid sawn timber joists.

Joist Hanger with Adjustable Height Strap - 75mm x 270mm

Height adjustable joist hanger for supporting timber joists from timber members.

Product Information:

- A galvanised joist hanger that provides great support with ease of installation.

- Wider strap provides more surface area on the supporting timber and allows increased nail spacing, enhancing the performance of the critical hanger-to-support part of the connection.

- Minimum and maximum nailing schedules are stamped into the strap providing correct installation information for site operatives.

- Speed-prong holds the hanger in position to allow easier attachment. The installer no longer has to try to hold hanger, joist and nail with one hand and swing a hammer with the other!

- JHA270 range features a location tab which allows easier alignment of the hanger.

- The model number and size is stamped into the seat of the hanger for easy identification, even after installation.

- Pre-galvanised mild steel.

Suitable on:

- Solid sawn timber joists.

When to use:

- Face Fix

- Wrap Over

Joist Hanger with Adjustable Height Strap - 75mm x 450mm

Height adjustable joist hanger for supporting timber joists from timber members.

Product Information:

- A galvanised joist hanger that provides great support with ease of installation.

- Wider strap provides more surface area on the supporting timber and allows increased nail spacing, enhancing the performance of the critical hanger-to-support part of the connection.

- Minimum and maximum nailing schedules are stamped into the strap providing correct installation information for site operatives.

- Speed-prong holds the hanger in position to allow easier attachment. The installer no longer has to try to hold hanger, joist and nail with one hand and swing a hammer with the other!

- JHA450 range features longer legs.

- The model number and size is stamped into the seat of the hanger for easy identification, even after installation.

- Pre-galvanised mild steel.

Suitable on:

- Solid sawn timber joists.

When to use:

- Face Fix

- Wrap Over

Joist Hanger with Adjustable Height Strap - 91mm x 270mm

Height adjustable joist hanger for supporting timber joists from timber members.

Product Information:

- A galvanised joist hanger that provides great support with ease of installation.

- Wider strap provides more surface area on the supporting timber and allows increased nail spacing, enhancing the performance of the critical hanger-to-support part of the connection.

- Minimum and maximum nailing schedules are stamped into the strap providing correct installation information for site operatives.

- Speed-prong holds the hanger in position to allow easier attachment. The installer no longer has to try to hold hanger, joist and nail with one hand and swing a hammer with the other!

- JHA270 range features a location tab which allows easier alignment of the hanger.

- The model number and size is stamped into the seat of the hanger for easy identification, even after installation.

- Pre-galvanised mild steel.

Suitable on:

- Solid sawn timber joists.

When to use:

- Face Fix

- Wrap Over